this product manufactured with lead-free processing pb do not scale from this print designed & dimensioned in millimeters[inches] rfxxx-xxxxx-xxxxxx-xxxx overall cable length millimeters of cable 0100 min. (see note 8 & 9) end 1 connector end 2 connector or preparation end 1 plating option 1: gold all components 2: gold / nickel combination 3: alternate gold / nickel (see sheet 3 for plating specifics) 1: gold all components 2: gold / nickel combination 3: alternate gold / nickel *(leave blank for -sing or -xxxxxx end 2 preparation) end 2 plating option -01sp: sma-p-c-x-st-ca1 (see sheet 3) -01rp: sma-p-c-x-ra-ca1 (see sheet 3) -01bj: sma-j-c-x-st-bh1 (see sheet 3) -01br: sma-j-c-x-st-br1 (see sheet 3) -02sj: mcx-j-c-x-st-ca1 (see sheet 3) -02rp: mcx-p-c-xx-ra-ca1 (see sheet 3) -02sp: mcx-p-c-xx-st-ca1 (see sheet 4) -03sp: mmcx-p-c-x-st-ca1 (see sheet 4) -03rp: mmcx-p-c-x-ra-ca1 (see sheet 4) -04sp: bnc5-p-c-xx-st-ca1 (see sheet 4) -04bj: bnc5-j-c-xx-st-bh1 (see sheet 4) -05sp: tnc-p-c-xx-st-ca1 (see sheet 4) -05bj: tnc-j-c-xx-st-bh1 (see sheet 5) -06bj: ntpe-j-c-xx-st-bh1 (see sheet 5) -07sp: smb5-p-c-xx-st-ca1 (see sheet 5) -07rp: smb5-p-c-xx-ra-ca1 (see sheet 5) -07bj: smb5-j-c-x-st-bh1 (see sheet 5) -13gp: grf1-p-c-x-st-ca1 (316 option only) (see sheet 5) -13gj: grf1-j-c-x-st-ca1 (316 option only) (see sheet 6) -01sb: sma-j-c-x-st-sb1 (see sheet 6) -01sr: sma-j-c-x-st-sr1 (see sheet 6) -sing: single ended (one end only, see note 11) -xxxxxx: stripped and tinned (this end only- see notes 11-15 & sheet 6, fig. 3) (see fig. 2) "c" format: x.x mm (see fig. 2) "b" format: x.x mm (see fig. 2) "a" format: x.x mm c 174: cca-174 (rg-174 coaxial cable) 316: cca-316 (rg-316 coaxial cable) cable call out -01sp: sma-p-c-x-st-ca1 (see sheet 3) -01rp: sma-p-c-x-ra-ca1 (see sheet 3) -01bj: sma-j-c-x-st-bh1 (see sheet 3) -01br: sma-j-c-x-st-br1 (see sheet 3) -02sj: mcx-j-c-x-st-ca1 (see sheet 3) -02rp: mcx-p-c-xx-ra-ca1 (see sheet 3) -02sp: mcx-p-c-xx-st-ca1 (see sheet 4) -03sp: mmcx-p-c-x-st-ca1 (see sheet 4) -03rp: mmcx-p-c-x-ra-ca1 (see sheet 4) -04sp: bnc5-p-c-xx-st-ca1 (see sheet 4) -04bj: bnc5-j-c-xx-st-bh1 (see sheet 4) -05sp: tnc-p-c-xx-st-ca1 (see sheet 4) -05bj: tnc-j-c-xx-st-bh1 (see sheet 5) -06bj: ntpe-j-c-xx-st-bh1 (see sheet 5) -07sp: smb5-p-c-xx-st-ca1 (see sheet 5) -07rp: smb5-p-c-xx-ra-ca1 (see sheet 5) -07bj: smb5-j-c-x-st-bh1 (see sheet 5) -13gp: grf1-p-c-x-st-ca1 (316 option only) (see sheet 5) -13gj: grf1-j-c-x-st-ca1 (316 option only) (see sheet 6) -01sb: sma-j-c-x-st-sb1 (see sheet 6) -01sr: sma-j-c-x-st-sr1 (see sheet 6) "a" mm "b" mm "c" mm "d" mm "e" mm fig.2 cable stripping dimensions per configurations (see table 1)(see notes 12,13,14,15) c c c c c c fig.1 rfxxx-01spx-01rpx-xxxx shown do not leave any space blank, each must contain a numeric character 0 thru 9. sheet of unless otherwise specified, dimensions are in millimeters [inches]. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: rf316 or rf-174 cable assembly by: rfxxx-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing tim p. 5/3/2005 6 1 sheet scale: 2:1 see end 1 and end 2 assembly prints f:\dwg\misc\mktg\rfxxx-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 notes: 1. represents a critical dimension. 2. cable cut length: = (length: xxxx) - (subtractor for end 1) - (subtractor for end 2). (see table 1 for subtractors) 3. assembly to be 100% tested for opens & shorts. 4. assembly to be 100% hi-pot tested per table 1. 5. after final electrical tests, label each cable assembly with 1 label -et 6. criticals on connector prints to be checked in process. 7. finished assemblies to be packaged per packaging standard co-hd-wi-3033-m. -lock washers, nuts, and gaskets to be shipped unassembled. 8. cable stocked in inches, 1 inch = 25.4 millimeters. 9. cable lengths longer than 1000 millimeters are not supported by s.i. test data. 10. minimum bend radius for rg174 = 25.4 [1.00] rg316 = 12.7 [.50] 11. for sing ended or stripped and tinned assemblies: make a double ended assembly at twice the cable length and test before cutting assembly in half. 12. dim "a", "b", and "c" have a minimum value of 0.0mm & a maximum value of 9.9mm. 13. production of strip and tin for center dielectic use: a. 14. production of strip and tin for shield use: d=a+b. 15. production of strip and tin for jacket use: e=a+b+c. 16. for -ra to -ra, connectors should both be oriented up. (see sheet 6, fig. 4) revision s
sheet of rf316 or rf-174 cable assembly by: rfxxx-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing tim p. 5/3/2005 6 2 sheet scale: 1:1 revision s f:\dwg\misc\mktg\rfxxx-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
-01bj (straight bulkhead jack) (use drawing no. sma-j-c-x-st-bh1 for assembly instructions) -02sj (straight jack) (use drawing no. mcx-j-c-x-st-ca1 for assembly instructions) -01rp (right angle plug) (use drawing no. sma-p-c-x-ra-ca1 for assembly instructions) plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-p-c-h-st-ca1) note: all critical dimensions on sma-p-c-x-st-ca1 that apply must be verified. note: all critical dimensions on sma-j-c-x-st-br1 that apply must be verified. note: all critical dimensions on sma-p-c-x-ra-ca1 that apply must be verified. note: all critical dimensions on mcx-j-c-x-st-ca1 that apply must be verified. note: all critical dimensions on sma-j-c-x-st-bh1 that apply must be verified. -01sp (straight plug) (use drawing no. sma-p-c-x-st-ca1 for assembly instructions) -01br (reversed polarity ) (straight bulkhead jack) (use drawing no. sma-j-c-x-st-br1 for assembly instructions) plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-p-c-h-ra-ca1) plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-bh1) plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-br1) plating options 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: mcx-p-c-h-ra-ca1) 2: 30" min. gold center contact 3" min. gold outer contact 100" min. nickel remaining metal parts (end connector p/n: mcx-p-c-hn-ra-ca1) note: all critical dimensions on mcx-p-c-xx-ra-ca1 that apply must be verified. -02rp (right angle plug) (use drawing no. mcx-p-c-xx-ra-ca1 for assembly instructions) plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: mcx-j-c-x-st-ca1) sheet of rf316 or rf-174 cable assembly by: rfxxx-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing tim p. 5/3/2005 6 3 sheet scale: 1:1 revision s f:\dwg\misc\mktg\rfxxx-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
-02sp (straight plug) (use drawing no. mcx-p-c-xx-st-ca1 for assembly instructions) note: all critical dimensions on mcx-p-c-xx-st-ca1 that apply must be verified. -03sp (straight plug) (use drawing no. mmcx-p-c-x-st-ca2 for assembly instructions) -03rp (right angle plug) (use drawing no. mmcx-p-c-x-ra-ca1 for assembly instructions) note: all critical dimensions on mmcx-p-c-x-ra-ca1 that apply must be verified. note: all critical dimensions on bnc5-p-c-xx-st-ca1 that apply must be verified. -04sp (straight plug) (use drawing no. bnc5-p-c-xx-st-ca1 for assembly instructions) -04bj (straight bulkhead jack) (use drawing no. bnc5-j-c-xx-st-bh1 for assembly instructions) plating options 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: mcx-p-c-h-st-ca1) 2: 30" min. gold center contact 3" min. gold outer contact 100" min. nickel remaining metal parts (end connector p/n: mcx-p-c-hn-st-ca1) note: all critical dimensions on mmcx-p-c-x-st-ca2 that apply must be verified. plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: mmcx-p-c-h-ra-ca1) plating options 2: 30" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: bnc5-p-c-hn-st-ca1) 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: bnc5-p-c-mn-st-ca1) plating options 2: 30" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: bnc5-j-c-hn-st-bh1) 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: bnc5-j-c-mn-st-bh1) note: all critical dimensions on bnc5-j-c-xx-st-bh1 that apply must be verified. note: all critical dimensions on tnc-p-c-xx-st-ca1 that apply must be verified. -05sp (straight plug) (use drawing no. tnc-p-c-xx-st-ca1 for assembly instructions) plating 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: tnc-p-c-mn-st-ca1) plating options 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: mmcx-p-c-h-st-ca2) 2: 30" min. gold center contact 3" min. gold outer contact 100" min. nickel remaining metal parts (end connector p/n: mmcx-p-c-hn-st-ca2) sheet of rf316 or rf-174 cable assembly by: rfxxx-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing tim p. 5/3/2005 6 4 sheet scale: 1:1 revision s f:\dwg\misc\mktg\rfxxx-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
-05bj (straight bulkhead jack) (use drawing no. tnc-j-c-xx-st-bh1 for assembly instructions) note: all critical dimensions on tnc-j-c-xx-st-bh1 that apply must be verified. -06bj (straight bulkhead jack) (use drawing no. ntpe-j-c-xx-st-bh1 for assembly instructions) note: all critical dimensions on ntpe-j-c-xx-st-bh1 that apply must be verified. -07sp (straight plug) (use drawing no. smb5-p-c-xx-st-ca1 for assembly instructions) note: all critical dimensions on smb5-p-c-xx-st-ca1 that apply must be verified. -07rp (right angle plug) (use drawing no. smb5-p-c-xx-ra-ca1 for assembly instructions) note: all critical dimensions on smb5-p-c-xx-ra-ca1 that apply must be verified. -07bj (straight bulkhead jack) (use drawing no. smb5-j-c-x-st-bh1 for assembly instructions) note: all critical dimensions on smb5-j-c-x-st-bh1 that apply must be verified. plating options 2: 30" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: tnc-j-c-hn-st-bh1) 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: tnc-j-c-mn-st-bh1) plating options 2: 30" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: ntpe-j-c-hn-st-bh1) 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: ntpe-j-c-mn-st-bh1) plating options 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: smb5-p-c-h-st-ca1) 2: 30" min. gold center contact 3" min. gold outer contact 100" min. nickel remaining metal parts (end connector p/n: smb5-p-c-hn-st-ca1) plating options 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: smb5-p-c-h-ra-ca1) 2: 30" min. gold center contact 3" min. gold outer contact 100" min. nickel remaining metal parts (end connector p/n: smb5-p-c-hn-ra-ca1) plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: smb5-j-c-h-st-bh1) -13gp (straight plug) (use drawing no. grf1-p-c-x-st-ca1 for assembly instructions) (316 option only) note: all critical dimensions on grf1-p-c-x-st-ca1 that apply must be verified. plating 1: 30" min. gold center contact 10" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: grf1-p-c-h-st-ca1) sheet of rf316 or rf-174 cable assembly by: rfxxx-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing tim p. 5/3/2005 6 5 sheet scale: 1:1 revision s f:\dwg\misc\mktg\rfxxx-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
fig. 3 rfxxx-04bjx-102148-xxxx shown rf316-01rpx-01rpx-xxxx shown (see note 16) fig. 4 note: all critical dimensions on grf1-j-c-x-st-ca1 that apply must be verified. -13gj (straight jack) (use drawing no. grf1-j-c-x-st-ca1 for assembly instructions) (316 option only) plating 1: 30" min. gold center contact 10" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: grf1-j-c-h-st-ca1) note: all critical dimensions on sma-j-c-x-st-sb1 that apply must be verified. plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-sb1) -01sb (sealed straight bulkhead jack) (use drawing no. sma-j-c-x-st-sb1 for assembly instructions) plating 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-sr1) -01sr reversed polarity (sealed straight bulkhead jack) (use drawing no. sma-j-c-x-st-sr1 for assembly instructions) note: all critical dimensions on sma-j-c-x-st-sr1 that apply must be verified. sheet of rf316 or rf-174 cable assembly by: rfxxx-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing tim p. 5/3/2005 6 6 sheet scale: 1:1 revision s f:\dwg\misc\mktg\rfxxx-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
